heating rate

英 [ˈhiːtɪŋ reɪt] 美 [ˈhiːtɪŋ reɪt]

加热速率

化学



双语例句

  1. Results show that those parameters such as temperature, water content, heating rate and calcination time have strong effects on average strength and its reliability of the catalysts.
    结果表明,温度、时间、升温速率和原料含水率对催化剂强度的均值和可靠性都有显著影响。
  2. The Boudouard reaction of carbon at low temperature was investigated by means of thermogravimetric method at constant heating rate.
    利用恒速升温热重法对低温下碳的气化反应进行了研究。
  3. The influences of heating rate and soaking time on piezoelectric and dielectric properties were also studied.
    并研究升温速度,保温时间对介电、压电性能的影响。
  4. The results showed that the heating rate plays a key role in affecting austenite grain growth.
    结果表明,加热速率对奥氏体化晶粒长大有显著影响。
  5. The sintering quality and shrinkage of the sintering parts were compared under vacuum or hydrogen atmosphere and different sintering temperature and heating rate.
    通过采用真空烧结和氢气气氛烧结、改变烧结升温速率和烧结温度,对比了烧结件的烧结质量和烧结收缩等情况。
  6. The Effect of Heating Rate on Microstructure and Electrical Properties of Varistor Ceramics
    升温速度对压敏瓷显微组织和电性能的影响
  7. The initial shrinkage temperature and the shrinkage change little with the increase of heating rate.
    升温速率增大,坯片开始收缩的温度及收缩率几乎不变。
  8. There is a negative feedback between the cooling rate of long wave radiation and the heating rate of short wave radiation.
    长波辐射冷却和短波辐射加热之间为近似负反馈的响应关系。
  9. An investigation on the devolatilization characteristics of pulverized corn stalk at fast heating rate in a laminar furnace;
    为研究闪速加热条件下生物质的热解挥发特性,设计了等离子体加热高温层流炉作为实验设备。
  10. Ohmic Heating Rate Model and Process Optimization for Colloidal Solution with Fruit Granules
    含水果颗粒胶体溶液通电加热速度建模与工艺优化
  11. Heating Rate and Temperature Distributing on Continuous Ohmic Heating for Liquid Food
    液态食品连续通电加热的加热速率与温度分布
  12. Effect of Grain Size and Heating Rate on Nitridation Reaction of Metallic Aluminium
    粒径与加热速度对金属Al氮化过程的影响
  13. Thermal Degradation Kinetics of PEN by Single Heating Rate Methods Kinetics of urease-catalyzed hydrolysis reaction of urea determined by isothermal titration calorimetry
    聚萘二甲酸乙二酯的热降解动力学&Ⅰ非等温热降解动力学等温滴定量热法测定脲酶催化尿素水解反应动力学
  14. The kinetic curing reaction of hybrid materials performs by differential scanning calorimetry ( DSC) technique at different heating rate.
    利用差示扫描量热仪对杂化材料的固化动力学进行了研究。
  15. The effects of heating rate and temperature on the pyrolysis behaviors of EMAL are investigated.
    探讨了升温速率和热解温度对毛竹EMAL热失重行为的影响。
  16. The experimental results indicated that the heating rate of the soybean sauce increased with increase of the voltage and the salt content and decrease of solid content.
    研究了不同欧姆加热条件对大豆酱电导率、加热速率以及酵母菌杀菌效果的影响。
  17. APPLICATION OF GA TO SHUTTLE KILN HEATING RATE OPTIMIZATION make lacework by knotting or looping.
    遗传算法优化燃气梭式窑升温速率的研究用梭编的方式制作花边。
  18. The SEM analysis results also show that the pore of hollow-porous carbon fiber regularly varies as the carbonization heating rate increases.
    SEM分析显示,随着炭化升温速率的升高,纤维的截面变形程度加剧,孔径增大。
  19. Reaction Device for Measuring the Dynamic Spontaneous Heating Rate of Oxidation for Sulfide Ore Sample and Its Numerical Simulation
    硫化矿石动态自热率测定装置及其数值模拟
  20. Effect of Carbonization Heating Rate on the Pore Structure of Hollow-Porous Carbon Fibers
    炭化升温速率对中空多孔炭纤维孔结构的影响
  21. Gas cavity and deformation of the samples can be avoided by degreasing and sintering at low heating rate.
    采用较低的升温速率脱脂和烧结时,能避免产生气泡和变形等缺陷。
  22. Influence of heating rate and water contents on sawdust pyrolysis process and characteristic
    升温速率和水分含量对木屑热解过程和特性的影响
  23. The superheating and melting behavior are found to be strongly affected by the heating rate.
    模拟中考虑了缺陷和表面对熔化和过热行为的影响。
  24. The affection of heating rate, heated history and load to the result of TMA measurement is discussed.
    讨论了升温速率,热历史和负载对TMA测定结果的影响。
  25. Effects of heating rate, sintering temperature, time for heat preservation and content of fly ash were investigated.
    考察了升温速率、烧成温度、保温时间以及粉煤灰的含量对陶粒的颗粒抗压强度和吸水率的影响。
  26. The experiment revealed influence of temperature, resistant time, heating rate and pressure to the yield of bio-oil.
    本实验主要考察了反应温度、停留时间、升温速率、催化剂和压力对产物收率的影响。
  27. Effect of heating rate and holding time on microstructure of brazing joint is analyzed.
    观察并分析了升温速率及保温时间对接头显微组织的影响。
  28. Burnout temperature of petroleum coke Increases with increase of heating rate.
    提高加热速率增加了石油焦的燃尽温度。
  29. Meanwhile, increasing the heating rate and prolonging the crystallization time can both increase the content of anorthite.
    同时,增大升温速率和延长晶化时间均能使样品中的钙长石含量增加。